WIRELESS 3D PROBE CONVERTER · NOW ON PRE-ORDER

Every touch,
on the record.

nc3DAir turns the popular, affordable USB-C 3D touch probe you already own into a wireless one, with a battery you recharge over USB-C. It plugs into the probe's USB-C socket; nothing on the probe changes. The probe stays in the tool rack, the cable is gone, and every touch reaches the controller in about 4 ms.

The transmitter goes on the probe and talks to the ncSender Wireless Receiver, sold separately, which wires to your controller. It's the same receiver AutoZeroAir uses, so one serves both. Any CNC controller with a probe or tool setter (TLS) input that can supply 5 to 24 V works, not only grblHAL or ncSender. The 3D probe itself is not included.

REPEATABILITY (CORE, 1σ)2.0 µm
A 3D touch probe in an ISO20 tool holder with nc3DAir mounted around it in a clear housing
TOUCH → CONTROLLER (MEDIAN)3.6 ms

Wireless, without the usual catch.

Keep the probe you trust. nc3DAir adds the radio and a battery you charge over USB-C.

A TR-3C style 3D touch probe with a USB-C socket, rated 5 to 24 V
MADE FOR THE TR-3C STYLE USB-C PROBE

The affordable probe you already have, made wireless.

The TR-3C style 3D touch probe is accurate, popular and cheap, but it needs a cable to the controller. nc3DAir plugs into its USB-C socket, powers it from a rechargeable battery and sends every touch to the receiver. Nothing on the probe changes.

INDUSTRIAL WIRELESS PROBE
  • Costs as much as a small machine
  • Its own receiver and interface to install
  • Battery service through the maker
CHEAP WIRELESS PROBE
  • Fiddly to set up and pair
  • Batteries drain quickly
  • Disposable cells, not rechargeable
NC3DAIR
  • Converts the affordable USB-C probe you already own
  • Rechargeable Li-ion, charged over USB-C
  • Sleeps in the rack, wakes on motion
  • Receiver wires in like a wired probe

A probe the tool changer can load.

No cable means the probe gets a tool number like any bit. Probe the part mid-job, with nobody at the machine.

  1. 01 · RACKAsleep in its slotDraws almost nothing, and so does the probe.
  2. 02 · PICK UPWakes on the liftA motion sensor wakes it as the spindle takes it.
  3. 03 · PROBETouch, in ~4 msStraight to the controller's probe input.
  4. 04 · RETURNBack to the rackThe next tool change puts it away. Cutting resumes.

Silence means stop. If the receiver stops hearing nc3DAir, because the battery is flat or it is out of range, it reports the probe as touched and the controller stops the move. Never a crash into the stock.

1000 touches on one edge. Here is where they landed.

G38.2 · F150 · grblHAL · 0 missed · 0 resets
The run on video

812 of 1000 within ±5 µm of the median: the core repeatability is about 2 µm.

991 of 1000 within 50 µm. The tail is the radio resending a packet, which shows as a slightly deeper touch.

+3 µm drift from the first 20 touches to the last 20. Prototype numbers, re-measured on production boards.

The receiver wires into your controller.

A small box with screw terminals. It takes power from the controller and drives the probe or TLS input like a wired probe would. Any CNC controller with one of those inputs works, no special firmware or software needed.

Sold separately, and the same receiver AutoZeroAir uses: if you already have one, it works with nc3DAir too.

Get the receiver · $75

The nc3DAir receiver board inside its enclosure, with screw terminals for power, the probe output and two inputs Exploded view of the receiver: enclosure top, the board with its terminals and USB-C port, and the base
  • 5 to 24 V inPowered from the controller through the same terminal as the probe output.
  • Two extra inputsHook up a tool setter or another sensor, 3.3 to 24 V signals. Each one shares the probe output.
  • Flip a switch to invertA DIP switch per input sets normally open or normally closed.
  • Lights you can readA status light for the link and a blue light per input when it triggers.
The nc3DAir board: a small radio module with its battery connector, USB-C port, pairing button and side-facing status light

The numbers

In the box
The nc3DAir transmitter. Receiver and 3D probe sold separately
Probe connection
USB-C plug, 5 V probe supply
Link
2.4 GHz direct, no Wi-Fi needed
Latency
3.6 ms median, 95% under 16 ms
Fail-safe
Lost link reads as touched
Power
3.7 V 300 mAh Li-ion, USB-C charging, wake on motion. Orders outside the USA ship without the battery
Controller
Any with a probe or TLS input, and 5 to 24 V for the receiver
Updates
Over the air from ncSender

PRE-ORDER · $99 · SHIPS DECEMBER 2026

Pre-order nc3DAir.

Charged when you order, and you can cancel for a full refund any time before it ships. Add the ncSender Wireless Receiver on the product page if you don't have one yet.

Pre-order nc3DAir